FP42ULC FP42MULC
FLAT PANEL CABINET CART WITH
OR WITHOUT A PULL OUT SHELF
WARNING: FP42 carts are intended to hold monitors up to 75 lbs. The
use of a TV monitor weighing more than that may result in instability
causing possible injury. The top, middle and bottom shelves are intended to
hold equipment up to 50 lbs. on each shelf. The pull out shelf on FP42MULC is
intended to support equipment up to 15 lbs.
PARTS LIST
HARDWARE LIST
Cart Models: FP42ULC & FP42MULC
Ref
AA
BB
CC
DD
EE
FF
GG
HH
II
Qty
22
24
2
2
4
12
2
2
2
4
4
4
2
1
2
1
1
1
Part#
Description
5/8” Square Head Bolts
Qty
1
1
2
1
1
1
2
1
1
1
1
1
2
2
2
2
Part#
Description
030-0300-10T
030-0002
030-0023
030-0024
030-0259
030-0304
030-1349
SC1048B
030-0207
030-0401
030-0411
030-0865
030-0354
010-1188
012-0286
010-1106
030-1352
030-0368
022-3065
022-3066
022-3067
010-5778
022-1414
010-1910
010-1908
010-1909
022-1415
022-1416
022-2827
022-3068
010-4953
010-4956
015-0017
015-0018
Right Rear Leg Assembly
Left Rear Leg Assembly
Front Leg Assemblies
Top Shelf
Middle Shelf
Bottom Shelf
Cabinet Side Panel
Cabinet Rear Panel
Right Door Assembly w/Lock
Left Door Assembly
Handle Assembly
Monitor Bracket
5/16-18 Hex Serrated Nuts
#6-32 x 3/8” Round Hd Machine Screws
#6-32 Hex Nuts
#10 x 1/2” Phillips Pan Hd Screws
1/4-20 X 1/20” Truss Hd Screws
5/16-18 x 3/4” Hex Hd Screws
1/4-20 x 45mm Bolts
1/4-20 Serrated Flange Nuts
5/8-18 x 1 1/2” Hex Head Screws
5/16-18 Serrated Nuts
#6 x 1/2” Button Pin-In Hd Screws
10-32 x 1 1/2” Button Sockets Screws
Door Stop
JJ
KK
LL
MM
Hook Bars
Stop Brackets
5” Stem Casters w/o Lock
5” Stem Casters with Lock
Plastic Handles
Hex Wrench
1/8” Security Pin-In Driver Bit
Replacement Key Set
Pull Out Shelf Models :
FP42MULC
Qty
2
1
1
1
Part#
Description
1
044-2124
Courtesy Hardware Pack
This Pack Consists of:
010-5783
010-5782
030-1468
030-1470
030-1471
Shelf Brackets
Pull Out Shelf
Left Outer Slide
Right Outer Slide
Inner Slides
(4) Metric M4 x 12 Screws
(4) Metric M4 x 30 Screws
(4) Metric M5 x 12 Screws
(4) Metric M5 x 30 Screws
(4) Metric M6 x 12 Screws
(4) Metric M6 x 35 Screws
(8) Small Washers
2
Electrical Unit Models :
Qty
1
FP42ULC-E5BK, FP42MULC-EBK,
Description
6-Outlet Electrical Unit
Part#
E6 UNIT
(20) Large Washers
(4) 5/8” Large Spacers
1
STEP 2
Slide the middle and bottom shelves onto the rear legs. Slide the front legs on. LOOSELY
install hardware to top shelf corner ONLY, remembering to leave access for the handle.
Slide on middle shelf.
Slide on bottom shelf.
Slide on front legs.
AA
BB
INSTALL HARDWARE TO TOP
SHELF CORNER ONLY, OMIT
HANDLE SIDE
AA
BB
3
STEP 3
Install handle to either side of the cart using bolts (GG) and nuts (BB).
GG
BB
STEP 4
Secure tube and top shelf together using screws (HH) and nuts (II).
HH
II
4
STEP 5
Position each side panel under the middle shelf and hook it’s bottom flange under the bottom shelf as
shown. LOOSELY install hardware to each corner with bolts (AA) and nuts (BB). Carefully rotate cart
onto it’s back and install rear panel just like side panels.
Side Panel
AA
BB
INSTALL HARDWARE TO
EACH CORNER
AA
BB
Rear Panel
NOW TIGHTEN ALL CART CORNER HARDWARE
5
STEP 6
Install door stop to bottom shelf using screws (CC) and nuts (DD).
CC
DD
STEP 7
Attach a handle to each door with screws (EE). Then install each door between the middle and bottom
shelves with screws (FF). NOTE: Adjustments to the door stop may need to be done.
FF
EE
6
STEP 8
Push a caster into each leg insert. To ensure casters are securely in place, a rubber mallet may be used
to tap them in place. NOTE: The locking casters MUST be installed on the same side as the handle.
STEP 9
Attach the monitor bracket onto the front of the rear leg tubes as shown using bolts (JJ) and nuts (KK).
JJ
KK
7
SKIP TO STEP 15 IF YOUR CART DOES NOT HAVE A SHELF
STEP 10
Attach each shelf bracket under the top shelf as shown using screws (FF).
Make sure the bracket
cutouts face this way, if not
the bracket will be installed
upside down.
FF
STEP 11
Install the outer slide onto the shelf bracket by sliding TAB 1 into CUTOUT A and TAB 2 into CUTOUT B.
The pull out shelf should be installed opposite of the handle.
This tab determines
where the shelf will
slide out from.
Each cart bracket has
additional cutouts to allow
the shelf to pull out from
either side of the cart.
NOTE: Some bend in the bracket is ok as the slides and shelf will take care of that once
they are installed.
8
STEP 12
Install each inner slide into the outer slides. NOTE: Push inner slide in all the way until it snaps in.
STEP 13
Extend the slides to the positioning shown.
9
STEP 14
Install the pull out shelf by sliding CUTOUT 1 into TAB 1 and CUTOUT 2 into TAB 2.
CUTOUT 2
TAB 1
TAB 2
CUTOUT 1
10
STEP 15
Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A
courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase
additional metric screws from your local hardware store for odd shaped monitors.
TOP
BOTTOM
STEP 16
With someone’s help, hook your monitor onto the bracket as shown. (Monitor removed from picture for clarity.)
MONITOR NOT
SHOWN FOR CLARITY
11
STEP 17
Attach the stop brackets to the hook bars as shown with security screws (LL) using the
driver bit provided.
LL
STEP 18
Center your monitor horizontally and then tighten in place with screws (MM).
MM
CENTER MONITOR HORIZONTALLY THEN SECURE
Part # 031-8691
Rev. 05.11.11 CZ
12
|
Beko Washer Dryer WCY71032HPTL User Manual
Black Box Switch KV0416A R2 User Manual
Black Decker Iron F611 User Manual
Blaupunkt Car Video System DVD ME1 User Manual
Braun Electric Toothbrush 7000 DLX series User Manual
Briggs Stratton Portable Generator 030325 User Manual
Brother Fax Machine FAX 2750 User Manual
Castelle Fax Machine 61 1273 001 User Manual
Chamberlain Automobile Electronics 942FP User Manual
Char Broil Gas Grill 463262811 User Manual